The blower is the muscle of the air system. A dust-loaded, out-of-balance wheel quietly gives up airflow, wastes energy and chews through bearings. We clean the whole assembly and verify it to the NADCA ACR Standard.
Most commercial air is moved by a centrifugal blower — a wheel of small curved blades spinning inside a scroll housing. Each blade is a tiny airfoil, and it only moves its rated air when it is clean. As dust cakes onto the blades, they change shape, the wheel loses capacity, and delivered CFM drops across the entire system it serves.
The buildup rarely lands evenly, so the wheel also goes out of balance. That imbalance becomes vibration, and vibration is what destroys bearings, loosens sheaves and cracks welds. So a fouled blower costs you twice — first in airflow and energy, then in the bearing and motor failures that follow.
IAQ Restoration cleans the complete blower assembly — wheel, housing, inlet, drive and shaft — restoring airflow and smoothing the wheel, then verifies the clean to the NADCA ACR Standard and documents it for your maintenance record.
A forward-curved blower wheel only delivers its rated CFM when the blades are clean and true. Dust changes their shape and throws the wheel out of balance — cutting airflow and feeding the vibration that kills bearings.
The full centrifugal blower — every surface that touches the airstream or turns with the wheel.
Caked buildup is removed from every blade so the wheel regains its shape, its rated CFM and its balance.
The scroll and cutoff are cleaned so the air leaving the wheel is not fighting its way through built-up debris.
A fouled inlet chokes the wheel before it even starts. We clean the cone and any inlet vanes to restore intake.
Motor, sheaves and belts are cleaned and checked so the drive turns the clean wheel without slipping or loading.
The shaft and bearing area are cleaned and inspected — the first place a neglected, vibrating blower shows wear.
We confirm the cleaned wheel runs smooth and that airflow is restored, not just that the surfaces look clean.
A clean, balanced wheel delivers its rated CFM again, so every zone downstream finally gets the air it was designed for.
A blower that moves air efficiently draws less power for the same result — and stops the system from over-running to compensate.
Balancing the wheel removes the vibration that destroys bearings, sheaves and welds — the root of most fan failures.
Cleaner, smoother-running blowers mean fewer bearing changes, fewer motor failures and fewer emergency service calls.
A documented process that follows the NADCA ACR Standard from lockout to airflow verification.
We inspect the wheel, housing, drive and bearings and record airflow and condition before any work begins.
The unit is placed under lockout/tagout so the wheel is safe to open, access and clean.
Containment and HEPA collection capture loosened debris so nothing migrates into the ductwork or space.
Every blade, the scroll, inlet and cutoff are cleaned back to bare surface to restore shape and airflow.
Belts, sheaves and bearings are checked and the wheel is confirmed to run smooth after cleaning.
Cleanliness is confirmed to the ACR Standard and delivered as a photo-documented closeout.
Packaged-unit blowers, AHU plug fans, return and exhaust fans, industrial process fans — cleaned to one standard nationwide.
We treat the goal as restored airflow, not just clean-looking blades, and we document the result.
Every cleaning closes with photos and ACR verification your reliability and warranty files can use.
Airflow and vibration tell the story before a failure does.
A clean blower feeding fouled coils or ducts can’t deliver clean air. Explore the connected components — or the commercial air duct cleaning pillar.
Blower cleaning is condition-based and usually done alongside coil and unit cleaning. NADCA and ASHRAE guidance is to inspect at least annually and clean when buildup, airflow loss or vibration appear. High-runtime and high-dust environments need it more often.
Yes. Dust cakes onto each blade of a centrifugal wheel and changes its shape, cutting delivered CFM. Removing that buildup restores the blade profile and the wheel balance, which brings airflow back toward the design value.
We clean the wheel evenly so it runs true and confirm it runs smooth. Where a wheel needs mechanical rebalancing beyond cleaning, we identify it and coordinate the right corrective step rather than leaving a vibration behind.
The unit is locked out during cleaning for safety, and we schedule that window around your operations — nights, weekends or phased zones — so the building keeps running. Call 800-883-6040 to plan it.
NADCA-certified blower and fan cleaning, verified to the ACR Standard and documented for your maintenance record. Book an assessment — we’ll scope it free.
📞 Call 800-883-6040 Request a Quote Online